Tuesday, October 17, 2017

Honest review of the Hot Steam Gravity Feed Steam Electric Iron SGB-600/SGB-900

I bought this iron back in 2015; although, I didn't get around to hanging it until late last year.  When I did finally unbox it, it didn't work.  I called customer service and they walked me through some diagnostics and when that failed, they shipped a new iron.  How's that for great customer service??

The iron presses very well, much better than my Rowenta.  It gets very, very hot and has a tremendous amount of steam.  However, it is like any other iron in that when I use it for extended periods of time, it will cool down and start spitting.  I was pressing large amounts of linen fabric when it started spitting and left a brown stain on my white linen.  Then I noticed the light had come on indicating that it was not at the correct temperature.


This is my setup.  Excuse my really stained press top.  It gets a lot of use!




If you plan on buying any type of gravity feed iron, I have a few tips:

First, see how the water tube and the electric cord are bound together with clips?  Those clips are supposed to keep them from getting tangled up.


That doesn't always work.  Why?

The water tube is hanging from the water reservoir from the ceiling.


While the cord is plugged in below. It's the gold outlet at the bottom of the picture.  I had my electrician install it before I put in the hard wood.  Sure wish I had taken a little closer shot.  But you get the idea.


If I could do this over again, I would have put my outlet in the ceiling next to where the reservoir hangs so they'd both be in the same place, and the cord is plenty long enough to do that.  They would still tangle a bit but not nearly as much. It is also easier to determine placement.  I laid out my room with tape before I laid the hardwood and got all the furniture placed.  That's hard to do when there is nothing else in the room.  If it were in the ceiling, it would make moving around my work table much easier.

Second, be absolutely certain you place the iron completely on the rubber mat.  If you don't, it will scorch the surface beneath.  I've made that mistake twice.

Third, this iron does not have an automatic shutoff and the light goes off when it's hot, not the other way around.  I like the no shutoff feature, so I don't have to wait for it to heat up again in between pressings.  Get in the habit of turning it off as soon as you know you won't need it anymore.  You can also put a note on your light switch or your door reminding you to turn it off when you leave the room.  Better yet, have your outlet connected to the switch, so you only have to turn the switch off to turn everything off.

Fourth, I do not like having to climb up on top of my table to turn the knob on my water reservoir when I need steam.  The instructions say to always turn the valve off when not in use.  So I climb up to turn it on and again when I turn it off.  It has to be 3 feet above the table, so I can't lower it.  I need some sort of pulley that I can lower it more easily.

All in all, this is a fantastic iron if you pay attention to the heat while using it.  It eliminates the need to have a boiler sitting on your table and getting in the way of your pressing.

Hope this helps if you are looking to buy a gravity feed iron.

Happy Tuesday!

Angela


12 comments:

  1. This comment has been removed by the author.

    ReplyDelete
  2. This comment has been removed by the author.

    ReplyDelete
  3. Hello. I've heard a lot about steam ironing, but I'm interested in their reliability. I read a few reviews, forums, but I did not find any useful information.

    I have a regular iron (with the possibility of steam supply) and if I do not use the steam for a long time when ironing, then rusty scum begins to form inside (I so ruined a white shirt, because I did not know about this feature). How are these things with steam irons? They always use water for ironing. Do they need to be washed or cleaned inside? Or should I use some kind of special water that will not leave behind this raid?

    ReplyDelete
    Replies
    1. They use distilled water so calcium doesn't build up. They will last a long time if you treat them right. I usually rise out and lightly clean the reservoir whenever it's empty and I refill it. I've already dropped mine and it's still working fine. I've left it on for more than a whole day because I forgot to turn it off and it didn't burn my house down! LOL

      You can use distilled water for your regular iron too, it's actually recommended and it'll help with the rust issue.

      Delete
    2. I'm sorry Alex, I'm just now seeing your question. I have no issues with the gravity feed with spots unless I am using it for a long period of time and I don't allow it to heat up again. It does cool off a bit with prolonged use. The gravity feed system comes with minerals that you add to the reservoir and use regular tap water. For regular steam irons, Nancy Zieman recommends using filtered refrigerator water to eliminate spitting and spotting. Also always empty your iron before storing it. I have a Rowenta that I use to iron laundry. I have not had a problem with it spitting or rusting since I started following her advice.

      Delete
  4. This comment has been removed by the author.

    ReplyDelete
  5. I really like your setup. I've been trying to find a better way to set up my gravity feed iron. I ran an extension cord up over the hook that the reservoir was handing from so that the cord and the tube were together from the same direction. That's weird about having to shut of the water supply all the time. I've never turned the water supply off unless I was moving the reservoir. It doesn't leak at all. :D

    ReplyDelete
    Replies
    1. Thank you. They recommend turning off the water supply, but I have since stopped that too. I have not had any problems with it leaking. But I still have to climb up to remove it to refill it. I actually have a pulley for it but haven't installed it yet. I may try your idea of using an extension cord to keep them together until I can get an outlet installed in the ceiling.

      Delete
  6. I have mine on a hook on top of a closet door.. Works just fine... I have one with the minerals in it... They can come out and stain your work... I just took the minerals out and use distilled water now... Thank heavens nothing important was stained.. I love this iron..Been using it for years..

    ReplyDelete
    Replies
    1. I have had mine for 4 years now and I have never had the minerals come out. Mine will spit occasionally if I do not allow it to warm up again after prolonged use. I wonder if yours is missing the filter at the top.

      Delete
  7. Loved your description, and work space..
    Suggestion to the plug in of cord..
    Surge protector attached to side of table..Then you will have full use,and ease in pressing.

    ReplyDelete
  8. Enjoyed reading the article above, Very interesting, good job and thanks for sharing!!




    Pay Someone To Do My Course Online For Me

    ReplyDelete